Yuxiao Z.
Sammamish
Appliance & Power Tool Hookup in Seattle
Dedicated circuits for electric dryers, ranges, wall ovens, cooktops, dishwashers, and microwaves, and 240V circuits for welders, saws, compressors and shop equipment. We always size the circuit to the nameplate so your new appliance runs properly.
Licensed, Bonded, & Insured
Over 100 Five-Star Reviews
Free Estimates
Upfront Pricing
Permits and Inspection Included
2-Year Warranty
WA Lic #CHARGCH761KL · Most jobs scheduled the same week
Dryers, Ranges, Saws and Welders
Appliance & Power Tool Circuits
Almost anything that heats or has a motor in it needs a circuit of its own, and which type of circuit and receptacle it needs is specific to the appliance. These are the ones we are asked for most:
Electric Dryers
Ranges, Ovens and Cooktops
Dishwashers and Disposals
Microwaves and Refrigerators
Table Saws and Planers
Welders and Plasma Cutters
Air Compressors and Dust Collectors
Garage and Shop Subpanels
Induction Ranges and Cooktops
An induction range pulls more than the coil range it replaces, commonly 40A or 50A at 240V. The number that matters is on the nameplate, not on the old breaker: a 40A circuit that fed a thirty-year-old range is not automatically enough to power the unit going in.
Going From Gas to Electric
A gas dryer or range has a standard 120V outlet behind it, while the electric equivalent usually needs 240V and a new receptacle. This conversion typically requires running a new circuit to the panel, and panel capacity can come into play if your panel doesn't have space for the additional load.
Will My Delivery Crew Handle It?
Delivery crews set and level an appliance. They do not add circuits, and most will not make a hardwired connection, so an appliance that arrives before its circuit is installed often sits in the kitchen until someone is able to come out and install it. Usually all we need is the model number and we can tell you what it needs to run same-day.
Power Tools and Shop Equipment
A garage wired for a light and a door opener will not carry a shop. Tool circuits are sized the same way the kitchen ones are, off the plate on the machine, and the number that matters is the startup draw rather than the running one.
Not sure which of these yours needs? Call (425) 202-5529 or submit the form with what you are putting in and we will tell you what it takes to run it.
What It Costs
What Determines Appliance & Tool Hookup Cost?
A hookup is typically priced per circuit, however, several factors can influence how much each costs to run each one:
Whether the Circuit Exists
Changing only the receptacle is much cheaper than a whole new circuit
Distance From the Panel
We typically charge by the foot for new circuits that are required
Walls and Access
Attic access is ideal, finished walls only means fishing cable and sometimes a patch
Panel Space and Capacity
If the panel is full, we need to make room to handle the additional circuit
Estimates are free and itemized per circuit so you know exactly what you be paying up front.
Does My Panel Have Space?
Your panel needs both physical space as well as load capacity to handle a new circuit. See our full page on panel changes and service upgrades for more details on options when you are out of space.
Call (425) 202-5529 or submit the form with a photo of your panel with the door open, a photo of the label inside it, and the model number of your new appliance and we can tell you if you have enough capacity in your existing panel or not.
Customer Reviews
Real Reviews From Greater Seattle Homeowners
Over 100 five-star reviews across Google, Yelp, and more. See all reviews
Common Questions
Frequently Asked Questions
It depends. Swapping a three-prong dryer receptacle for a four-prong one on sound existing cable is the low end. Running a new 30A/240V circuit from the panel to a laundry room that has never had one costs several times that, and the distance and the walls in between decide where in that range it lands. Every estimate is free and itemized.
If the existing cable has a separate ground, we change the receptacle. If it is the older three-wire cable with no ground, common in homes wired before the mid-90s, the run has to be replaced to take a four-prong outlet. Buying a three-prong cord to fit the old outlet is legal on an existing installation but it gives up the separate ground, so we do not recommend it.
A new circuit needs an electrical permit and an inspection in Washington. Replacing a receptacle on an existing circuit generally does not. We pull the permit and schedule the inspection as part of the job, and the fee is a line on your estimate rather than a surprise later.
We make the electrical connection and we will confirm the appliance powers up and runs. We do not do gas lines, water supply, or drain plumbing, and we do not set built-in units into cabinetry. A dishwasher or a gas range needs a plumber or the delivery crew alongside us.
Changing a receptacle is under an hour. A new 240V circuit is usually half a day, and longer if the cable has to be fished through finished walls or the panel needs a subpanel first. We give you the time estimate with the price.
The big ones cannot. A dryer, a range, a dishwasher, a disposal, and a microwave each need a circuit of their own, which is why a kitchen remodel adds several breakers rather than one. Small countertop appliances share the kitchen's general receptacle circuits, and there are normally two of those.
Yes, and it is cheaper than booking them separately, because the panel work, the permit, and the trip are shared. If you are replacing a kitchen's worth of appliances, send the whole list and we will price it as one job.
Yes. A detached building is fed by one buried feeder from the house and a small subpanel at the far end, and the tool circuits, the lights, and the outlets all come off that panel. It costs more up front than running a single circuit out there, but it is the only version that leaves room for the next tool.
Free Estimate
Get Your Free Estimate
We respond to most requests within the hour, but will get back to you within a day at the latest.
What's Included in Every Hookup
- Licensed, insured electricians
- Circuits sized to the nameplate
- Panel capacity checked first
- Permits pulled where required
- Upfront pricing before we start
- Workmanship warranty
Prefer to talk it through?
How It Works
From Nameplate to Plugged In
1
Send Us the Appliance
Call or send the form with the model number, where the appliance or tool is going, and any delivery date you are working to. A photo of the nameplate and one of your open panel answers most of what we need.
2
Free Estimate
A licensed electrician checks the panel, walks the cable route, and prices the circuit and the connection on one itemized sheet. You see the number before any work starts.
3
Circuit In Before Delivery
We schedule the circuit ahead of the truck wherever the date allows, then make the final connection and confirm the appliance runs on it.
Our Service Area
Appliance & Power Tool Hookups Across Greater Seattle
We run dedicated circuits for electric dryers, ranges, wall ovens, induction cooktops, dishwashers, disposals, and microwaves, and 240V circuits and subpanels for welders, saws, compressors and detached shops, from Seattle to Mount Vernon. Free estimates, upfront pricing, and a full warranty are the In Charge Home Electric standard for all projects.
Our service area includes
SeattleBellevueRentonKirklandRedmondBothellShorelineBurienTukwilaEverettArlingtonMount VernonLynnwoodMarysvilleEdmondsKenmoreMercer IslandSnohomishSammamishMedina
and surrounding communities
You Might Also Need
